Ronbo

I do it all the time.

Call them up. They have no problem refunding your money if it doesn't work with your truck. You will know right away. On my kenworth it doesn't see the idle so it will go asleep after the predetermined time while sitting still. Doesn't affect anything because I apply the brakes prior to putting into gear and that wakes it up. Great customer service too. They had a bad batch of displays that would go dim and they replaced it with no problem.

If possible could you send them to me too? I need to repair mine as well.

The t2000 has motors that move the doors. They are on top

Kenworth dealer can print you out pictures. Your blend door has to be in defrost when removing the assembly from firewall. I haven't done it yet. Take a lot of pictures if you do. I believe I have a stick blend door for the dash vents. From what I have read dirt can get in there and bind them up. It looks like I may be able to get to it by pulling out the ad coils and the heater core. It looks like they just slide out after some removal of panels. Let me know

I had my solinoids replaced u dear warranty. It still drifted. They sent me a new cylinder to install. As I was loosening up the hose to the cylinder, a large amount of art escaped. I just tightened it back up. Problem solved. The system is supposed to be self purging. It is for the jacks, but the slide cylinders are on the side and the port is on the side so almost impossible to remove all the ar from the slide cylinders. Also they don't fully extend or retract so there will be trapped air unless you unbolt the cylinder and hold one end lower than the other and fully retract and extend it a few times.

We are in Phoenix, Az. I am in the hospital bing worked up for a bone lesion in the left femur. Sure am glad this did not occur before my medicare went into effect last year.

How far are you from West Sacra,ento? I need someplace to goof off this winter

Sounds love you will take a hit to swap it out. You could always weld 4 small legs on the hitch to keel it from tilting. Seen it done on Comercial rigs that haul dump trailers.

We have been in PA for about 2 months. We move to Hershey Thousand Trails on Monday for 2 weeks. We will then start to mosey towards Hutchinson, Kansas for the HDT rally in october.

I tie to the frame. If you tie to the axle the body can bounce up quite a bit. I think best bet is to move hitch back some.

Looks nice. Will we see in in October at the rally?

We at at the Escapees park north of Knoxville, Tn. Raccoon something. Two other HDT's in the park but don't see any owners

we are at Maumelle COE outside Little Rock. extremely nice park and large sites.Weather is warm but beaable. better than OK any time.

They will just slide along the pavement until you hit a ridge. Then contact your insurance co.

.43 is less than 2 quarts. Should be able to overfill the current tank

Hope you get feeling better soon

We are now at Fiesta Key. The park is pretty tight. I couldn't turn on the road for the pull through as it was too tight. Turns out I had bad directions anyhow. Went all the way around and came up from other direction. Found site and was ready to go around again and come in correct road. Theresa says just back inn you can do it. Nailed it first time. Had a large audience. The new ET is awesome by the way.

Take the clamp off. Wrap junction in aluminum foil. Reinstall clamp

There is only a small number of counties with emission testing. Brazoria county was given numbers to reduce their emissions to. We were already below that number. Harris county claims their pollution comes from the surrounding counties. We are on the hook only 6 more weeks.

JC what do they charge for the infield parking and what services are provided?

The tax office is 1 mile from the house. I think you can register up to 3 mos early or is that license.

i will just renew everything for 3 years when due. that will give them time to work it all out.