Jump to content

Progress on our Peterbilt


CrazyCooter

Recommended Posts

I haven't really posted up anything on here about the truck or any pics of what we have been doing to it since acquiring it last month. Figured I would start this thread and update as we go along since it will be a long tem project.

 

Picked our already started motorhome project, a 1999 Pete 385 48" sleeper from another member in So Cal early June and brought it 700 miles home without incident. It came with low mileage for it's age 681K, C12 13spd, singled with 3.90 ratio, and Lopro 24.5's. It also came with 24x60" underbed boxes and most of the steel to finish the 16' deck.

20150606_115719_zps9kv6wocx.jpg

 

We had no 5th wheel hitch on the Pete so had to do something about that! I have been towing with the B&W platform about 4 years and figured I would stick with it and use an air hitch for the trailer. This way the trailer would have air ride with either vehicle pulling it. Got a B&W flatbed weld in gooseneck and fabbed up a plate to put between the frame rails. Joe had left plenty of room when building the bed to put the hitch right at the rear of the bed.....7' behind the axle. This will hopefully leave room for putting my Jeep on the deck as well as pulling the 5er.

20150613_130651_zpshqhjjfwh.jpg

20150613_131829_zps7mfoadmb.jpg

20150614_132858_zpsqn354atk.jpg

Had to bend the locking lever a bit to allow clearance for the rocking of the plate.

20150614_132905_zpszxsj3lqd.jpg

Edited by CrazyCooter

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

  • Replies 235
  • Created
  • Last Reply

Top Posters In This Topic

All hooked up! Had to wait till the next day for a road test when I get the Hayes Air controller and wiring installed.....The waiting was killing me!

20150613_153848_zps2hfbgtid.jpg

 

We were running a shorter 0719 Morryde pinbox since we were towing with a longbed and no need for the extended. Well, I thought we might need that extra 9" for Jeep clearance so I got the original length1621 FlexAir replacement. I'm still playing with it becuase it didn't line up in the holes perfectly and it's going to raise the front 2" minimum.....not what I had in mind. It also has a little clearance issue with the body....Like I said, working on that.

20150628_194656_zpsiqcn5goh.jpg

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

Fast forward to this week where I decided to get the plate permanently mounted to it wont look like a work truck with the straps holding the load on...... Figured with 14" centers on the xmembers, there was a possibility of the Jeep bending the deck when strapped and bouncing around, so I welded in 1x2" .180 tube in between and 1" flat in the center where the sheets of .125 steel diamond plate will come together.

 

20150713_174357_zpsrd8zy23m.jpg

20150717_133610_zpsxcrthbxm.jpg

20150717_133555_zpsfdn3s0pb.jpg

 

I'll probably fire up the plasma cutter and start fitting those sheets tomorrow.

Edited by CrazyCooter

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

In the quest for better fuel economy, more usable gears, and lower rpm's when traveling in states who have a more reasonable speed limit than our lovely CA......I knew I wanted taller gears as I was taking off in 3rd loaded and that left 2 more gears on the table down low that were toatally wasted and needed at least one more OD gear, so I selected 3.36's since we do still travel in CA and the math worked out where 3.08's would have either put us lugging or revving at 60 mph in either 11th or 12th gear. I also knew I would be needing a locker since 95% of out camping is off the road 10 miles or more..... I did some shopping for the obvious choice.....The air locking RD404 cousin to our RS404 rear axle...... They were WAY proud of those and not like I had a like core to give back, so I went for the more affordable Detroit Locker instead. Figured while I was there might as well get bearings and make the job complete! Found the Ring/Pinion set and bearing kit on Ebay as new old stock for a much discounted rate....SCORE! I also had a good supplier for the Detroit since I'm kind of in the business although my supplier only does light duty stuff, they were able to order me the big guy.

 

This was today's project:

received_10203404394228995_zpsz2uopppl.j

 

Made a little stand to hold it since this stuff is heavy

20150718_122037_zpsiipez8l1.jpg

 

Spiders swapped, new bearings, and ring gear bolted on.

20150718_144958_zpsnlaeouv5.jpg

 

Ready to drop back in!

received_10203405200249145_zpss13agyei.j

 

Also visited a local engine builder/tuner this morning..... My ecm was loaded with the 430/1650 tune, so I left well enough alone there. She (Yes SHE Lol) made some changes to low end fueling that made a real difference in tip in and set the Jakes to work with the cruise on and to come on 1mph over the set point. I could now spin the rear tires while entering the freeway......Later on in the day, the Detroit fixed that!

 

Between the taller gears allowing longer between shifts and the snappier throttle, she's a real joy to drive now! The Gearmaster was showing 11.6mpg at 70 mph on my 15 mile road test. It has been accurate up to this point, but will have to double check with the new tune.....It's user adjustable thank goodness!

Edited by CrazyCooter

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

Looks nice. Will we see in in October at the rally?

I wish! We're still working and I don't think I could get enough time off to make the round trip drive.....

 

I'll post up some more later! Have to BBQ now...... You would think the wench would find something else for dinner the way I have been working this week..... :wub:

Edited by CrazyCooter

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

That ring and pinion looks a little heavier than the last 9" swap I did!

Nice work!

LOL! A little bit.... My wife helps me around the shop and knows what a 9", Dana 80, Toyota 8", etc look like. I sent her a pic of this Eaton gear vs. Dana 80 and she about flipped! She was wondering how I was going to manage working on the big stuff alone....Work smart, not hard!

 

11694758_960231914037783_878648872382276

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

Even managed to get Tracie behind the wheel.

 

She did much better than I expected first trip out with the grabby clutch, weird air brake pedal feel, and floating the gears. Told her to hurry up and get this down so I can be in the back surfing the web and drinking margaritas! It will be nice to have someone to maybe drive a couple hundred miles on the long days so I don't have to do it all.

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

I'll keep putting stuff up here. I always enjoy the pics everyone else has put up. Lots of good ideas and improvements come from sharing.

 

This is probably the one you are thinking of. We picked it up in that area.

 

Too many Volvo people around here, you know the kind.... ;)

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

Nice work. We'll be in Redding Labor Day weekend. We will have to get together so I can check everything out in person.

2000 Kenworth T2000 w/ Cummins N14 and autoshift
2017 DRV Mobile Suite 40KSSB4 with factory mods, dealer mods and personal mods - now in the RV graveyard
2022 DRV Full House MX450 with customized floor plan
2018 Polaris RZR Turbo S (fits in the garage)
2016 Smart Car (fits in the garage or gets flat towed behind the DRV when the RZR is in the garage)
My First Solar Install Thread
My Second Solar Install Thread & Photos and Documents Related to the build
My MX450's solar, battery and inverter system - my biggest system yet!

chadheiser.com      West Coast HDT Rally Website

event.png    

AZCACOIDIAKSMNMOMTNENVNMNDOKSDTNTXUTWYxlg.jpg

 

Link to comment
Share on other sites

Thanks guys!

 

Spent the afternoon getting the decking on the bed. I was really worried about warping 10' long sheets while plasma cutting, but didn't feel like loading it up for someone to sheer the plates. The fit came out pretty good overall and almost every box in the bed was perfectly square??!! Joe (Goldrush) did a good job when putting this together!

20150719_145507_zpsiheiujpz.jpg

20150719_154905_zpssysuwjji.jpg

20150719_164544_zpsc6stawca.jpg

 

I decided to do it that hard way and screw the sheets down in case I ever want to modify something or need easy access to something underneath. I used semi self tapping 1/4" T30 torx deck screws and countersunk them. I have to pull the sheets one more time to paint the framework and the undersides of the plates plus a lot more screws to drill, but at least they are fastened down for the time being!

 

Pretty impressed that I was able to do all of this without assistance...thank goodness for the forklift!

20150719_164022_zpsjjayjn5b.jpg

 

Ordered up a quad band ham radio for it today and thinking about some solar up on the sleeper to keep things topped off while running the refer.

 

Next on the agenda are mounting the tool boxes under the bed. This truck came with weedburner exhaust already but will have to extend the tailpipe at least 5' to the rear. Not that it's loud anyway, but hoping that will make the cab quieter.....

 

Have some Atlas II Leather seats coming next week!

Edited by CrazyCooter

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

Nice work. We'll be in Redding Labor Day weekend. We will have to get together so I can check everything out in person.

Absolutely! May have something to look at by then..... Edited by CrazyCooter

1999 Peterbilt 385 C12 430/1650 13spd

2006 Dodge 3500 DRW 4x4

2010 Hitchhiker Champagne 36 LKRSB

Link to comment
Share on other sites

Looking good. Is it correct that you went from a taller ratio of 3:08 to 3:36? It must have been lugging it with the 3:08 so when you went to the 3:36 it must have gotten it into the power band more to help improve the fuel mileage. Most people would have tried gong the other way to improve mileage.

Dave

2005 Freightliner Century S/T, Singled, Air ride ET Jr. hitch
2019 46'+ Dune Sport Man Cave custom 5th wheel toy hauler
Owner of the 1978 Custom Van "Star Dreamer" which might be seen at a local car show near you!

 

Check out http://www.hhrvresource.com/

for much more info on HDT's.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

RVers Online University

campgroundviews.com

RV Destinations

Find out more or sign up for Escapees RV'ers Bootcamp.

Advertise your product or service here.

The Rvers- Now Streaming

RVTravel.com Logo



×
×
  • Create New...